stk500_getsync - 搜索

约 32,700 个结果

在新选项卡中打开链接

Arduino Stack Exchange
https://arduino.stackexchange.com › questions
How do I resolve "avrdude: stk500_recv (): programmer is
Whenever I try to program my Arduino UNO Rev.3, I'm seeing the following error avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 1 of 10: not …
- 评论数: 8
- "avrdude: stk500_getsync(): not in sync: resp=0x00," aka Some D…
  I had this error in my Linux Mint 17.3 laptop with Arduino Nano avrdude: stk500_getsync(): not in sync: resp=0x00. Solved: removed all that had '…
仅显示来自 arduino.stackexchange.com 的搜索结果
CSDN博客
https://blog.csdn.net › article › details
Arduino笔记-解决上传时出现avrdude: stk500_getsync …
2020年6月17日 · 1、将程序上传到板子时Arduino IDE提示“avrdude： stk500_getsync（）： not in sync： resp=0x00” 网上查遇到这个问题的人比较多，有说驱动问题的，有说IDE设置问题的。具体到我遇到的这个情况，原因是 …
Instructables
https://www.instructables.com
Solution: Avrdude Stk500_getsync(): Not in Sync …
avrdude stk500_getsync() not in sync resp=0x30 for a response. This board however worked seamlessly with my Linux machine. After much searching …
预计阅读时间：5 分钟
Arduino Stack Exchange
https://arduino.stackexchange.com › questi…
"avrdude: stk500_getsync(): not in sync: resp=0x00," …
2014年2月12日 · I had this error in my Linux Mint 17.3 laptop with Arduino Nano avrdude: stk500_getsync(): not in sync: resp=0x00. Solved: removed all that …
评论数: 8
This is caused by a generic connection error between your computer and the Arduino, and can result from many different specific problems. Here are...
最佳答案
·
99
Another fix: Change Tools->Processor->Atmega 328P to Atmega 328P (Old Bootloader). Remind that the Processor option is only available when you sel...
57
Unfortunately, it can also mean that you burned your microcontroller. Were you doing anything dangerous right before you tried to upload a new sket...
12
If none of the above steps work, try reinstalling Avrdude and the avr-gcc compiler. I had to do this after my Mega started suffering from this. If...
10
I've had the same message. Every time it has been solved by selecting the right port ie USB under the menu Tools then Ports. Its a simple step but...
9
In my case I hadn't wired the RTS pin of the FTDI chip to a capacitor which went to the RST pin of the Arduino Pro Mini. Once I installed this conn...
9
I had the exact same problem. I tried installing the IDE in another laptop and uploaded the program from that laptop. Problem solved. Then I came b...
6
For people using Linux Mint I found that by selecting the "TTY SO" port instead of the one labeled "Arduino" it would work (I can't tell you exactl...
4
I uninstalled the IDE and drivers etc, installed it all again, then I ran the Arduino IDE as an administrator and set to run compatibility as windo...
4
An unusual one but I've been swapping out the microcontrollers a lot and i got this error when one wasn't seated correctly.. i was able to burn a f...
3
CSDN博客
https://blog.csdn.net › article › details
Arduino烧录程序出现avrdude: stk500_getsync() attempt x(1-10) of …
2021年5月15日 · avrdude: stk500_getsync(): not in sync: resp=0x00错误提示在arduino IDE中非常常见，这个错误代表着就是无法通过USB口与arduino控制板进行通信，下面总结一下这个 …
CSDN博客
https://blog.csdn.net › blueisman › article › d…
Arduino nano板上传项目出现avrdude: stk500_getsync …
2021年1月27日 · 某宝上买的Arduino nano板上传项目出现：avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00问题. 更改处理器为：ATmega328P (Old Bootloader)即可，如下图：顺利上传。
51CTO
https://blog.51cto.com
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x00
2024年11月12日 · 这行表示 avrdude 操作已经完成。. 可能的原因及解决方法：硬件连接问题:; 确保 Arduino 板正确连接到计算机的 USB 端口。检查是否有松动或损坏的连接。
博客园
https://www.cnblogs.com › perfy
avrdude: stk500_getsync (): not in sync: resp=0x00 - 博 …
2013年9月3日 · avrdude: stk500_getsync(): not in sync: resp=0x00错误提示在arduino IDE中非常常见，这个错误代表着就是无法通过USB口与arduino控制板进行通信，下面总结一下这个问题常见的几个原因。
爱代码爱编程
https://icode.best
Arduino烧录程序出现avrdude: stk500_getsync() attempt x(1-10) of …
2021年5月15日 · 最近好多Arduino爱好者在拿到Arduino控制器后通过Arduino IDE下载程序时出现了如下错误：”avrdude: stk500_getsync(): not in sync: resp=0x00“这个错误提示在Arduino …
百度知道
https://zhidao.baidu.com › question
给飞控板烧得arduino的bootloader 烧程序烧不进去？_百度知道
2024年12月3日 · 给飞控板烧得arduino的bootloader 烧程序烧不进去？在Arduino IDE中，您可能会遇到“avrdude: stk500_getsync(): not in sync: resp=0x00”这一错误提示，这通常意味着程序 …
其他用户还搜索过
stk500_getsync 的相关搜索
某些结果已被删除
分页
- 1
- 2
- 3
- 4
- 下一页